Products / 1:35th Accessories

Everything to perfect your models from updates to stowage, supplies and traffic cones!

A182
£8.00

Israeli AFV searchlight from the 1960’s era. This fitment is common on IDF armour- AMX13, M50, M51, Shot, Shot Cal, M48 and Half Tracks. This set is designed to allow the buyer to replace the reflector with one from a Maglite torch if desired (not supplied) …

A181
£13.00

Set of 12 Israeli Soft-skin Jerry Can Holders in photo etched brass and resin. This type of holder is common on most types of IDF soft-skin vehicles. Full strap and buckle detail is included as are 12 IDF style Jerry Cans …

A180
£13.00

Set of 12 Israeli AFV Jerry Can Holders in photo etched brass and resin. This type of holder is common on most types of IDF armoured vehicles. Full strap, buckle and bolt detail is included …

A179
£13.00

Israeli .30 Cal MG Ammo Box Holders in three sizes, 2, 3 and 4 box. Two of each type are included with a total of 18 ammo boxes. Complete with straps this spring loaded type boxes are commonly seen on IDF vehicles, inside and out …

A178
£25.50

Designed to take the sting out of a bulk load of Jerry cans, this impressive stack of approximately 280 cans saves you around £140 over 17 sets of our regular Jerry Cans (A113)! And we have done most of the work for you with almost all the caps and nearly half the the handles already fitted, not to mention the cleaning up!…

A177
£11.00

This 1/35th scale set represents the Spineboards used by many western armies especially in theatres like Iraq and Afghanistan where the bulk of casualties are as a result of Improvised Explosive Devices (IED’s) that often lead to spinal injury. Initially when deployed the spineboards were yellow until a NATO green version was procured. The set contains 4 spineboards and 3 etched brass straps per board …

A176
£17.00

This 1/35th scale resin accessory set allows the detailing of the drivers position inside AFV Club Centurion kits. The all resin set designed by Rob Tearle includes side and rear bulkheads, drivers seat, controls and fittings and is suitable for all early marks of Centurion up to Mk-5. A detailed replacement roof panel is also included …

A175
£13.00

This 1/35th scale set represents the ‘Cots’ used by many western armies but very much the standard for the U.S. Army since World War 2. Originally made from wood and steel the frame design is unchanged to this day and is also made under licence in the UK (generally referred to as ‘Camp Beds’). From the Vietnam era, Aluminium was used and a lighter nylon carry bag employed. The set contains three bagged cots, three folded un-bagged cots …

A173
£15.00

A set of 6 1/35th scale resin cast concrete road barrier blocks. This set is suitable for use in the UK and Northern Ireland or anywhere as an improvised vehicle barriers for light non military vehicles …

A172
£13.00

A set of four 1/35th scale crowd control barriers in resin and etched brass. These interlocking galvanised steel barriers are typical in the UK, Northern Ireland (and elsewhere) for crowd control. Each barrier panel is 2”(52mm) wide x 1.5”(30mm) tall …

A171
£8.50

A set of two 1/35th scale Stop Checkpoint signs in etched brass with waterslide decals. This set is suitable for use in the UK and Northern Ireland …

A170
£5.50

This 1/35th scale fuel filler cap set by Rob Tearle converts plastic or resin kits with solid moulded on fuel filler covers to allow the covers to open and to have the correct removable inner caps (or caps and spout) details shown so that the model can be depicted being fuelled or serviced. The set can be used with our UBRE fuelling system or any other similar modern fuelling method …

A169
£5.50

This 1/35th scale fuel filler cap set by Rob Tearle converts plastic or resin kits with solid moulded on fuel filler covers to allow the covers to open and to have the correct removable inner caps (or caps and spout) details shown so that the model can be depicted being fuelled or serviced. The set can be used with our UBRE fuelling system or any other similar modern fuelling method …

A168
£5.50

This 1/35th scale fuel filler cap set by Rob Tearle converts plastic or resin kits with solid moulded on fuel filler covers to allow the covers to open and to have the correct removable inner caps (or caps and spout) details shown so that the model can be depicted being fuelled or serviced. The set can be used with our UBRE fuelling system or any other similar modern fuelling method …

A167
£5.50

This 1/35th scale fuel filler cap set by Rob Tearle converts plastic or resin kits with solid moulded on fuel filler covers to allow the covers to open and to have the correct removable inner caps (or caps and spout) details shown so that the model can be depicted being fuelled or serviced. The set can be used with our UBRE fuelling system or any other similar modern fuelling method …

A166
£5.50

This 1/35th scale fuel filler cap set by Rob Tearle converts plastic or resin kits with solid moulded on fuel filler covers to allow the covers to open and to have the correct removable inner caps (or caps and spout) details shown so that the model can be depicted being fuelled or serviced. …

A165
£5.50

This 1/35th scale fuel filler cap set by Rob Tearle converts plastic or resin kits with solid moulded on fuel filler covers to allow the covers to open and to have the correct removable inner caps (or caps and spout) details shown so that the model can be depicted being fuelled or serviced. The set can be used with our UBRE fuelling system or any other similar modern fuelling method …